puzbiks1
Comments
-
Sounds good.
-
>
-
@jebroad I ordered 20 of the SMM magnets. I am going to coat some using sodium silicate and aerogel. I put some of the aerogel in a rock tumbler a few months ago along with steel balls. I ran it for a month. When it came out I had a super fine powder. I will mix it with the sodium silicate and then test it. If all goes…
-
@birdhandz GE fuzed quartz has a tensile strenth of 7,000 psi and a compression strenth of 160,000 psi. The only reason I chose the double tube is the quartz becomes soft at around 1,700 C. I see no reason why it should not be biosafe.
-
@Birdhandz I will have to try sealing it direct with heat. @Jonny3D the powder from United Nuclear is a lot brighter. I have a few of the tritium keychains. After about 4 hours the powder is about equal in brightness to the tritium tubes.
-
@Jonny3D try whaleapparatus.com. I buy the quartz rod and tubing. It takes a higher temperature to soften but I have never had a problem. I am currently using a 4 mm tube and putting in Europium glow in the dark powder from United Nuclear. I am going to seal both ends with 4 mm rod using an epoxy. I will then place this in…
-
@Semilovr12 what lube did you use?
-
I purchased 30 2ml vials. I used one vial a day for 30 days injecting it direcly into my vein over a period of 10 min. After about a week I began seeing a few changes. I could study for hours with almost no breaks. About a week after finishing vial number 30 that is when things got a little crazy. I can only sleep 2 or 3…
-
How about the Europium Ultra Glow powder sold by United Nuclear?
-
Is it possible to get one without the anti- migration coating?
-
@ightden LOL. Way too many.
-
@cassox a little instruction would be great. I had figured just injecting 1 or 5 ml directly.
-
Can celebrolysin 1 ml be injected IV?
-
Vote Clinton for prison 2016.
-
@alexsmith I want the flat version.
-
I would be glad to participate.
-
@vatrat So far it has been about three weeks. I put a magnet in the right pointer and ring fingers. I used the lidocaine powder and followed the instructions I found on a survival website. I put in one stitch in each finger. They have healed up great.
-
I ordered a few of the gold plated magnets. I plated them in rhodium and now am going to coat them in the FDA2T. If three coatings fail then so he it.
-
Why four injections? I was told to use the transthecal digital block. I was told you only need 2.5-3 ml and one injection. Is this correct?
-
I chewed coca leave in Bolivia for three years. Yes you can go all day without eating but it does catch up with you real fast. I also used it for altitude sickness and never had any problems in La Paz or Potosi even at altitudes of over 13,000 feet. Another way to use it is to boil the leaves and distill it off. They call…
-
@minnella My magnets are coated nickel, copper, nickel. I am planning to put one on the side of the index finger and the other in the ring finger. The reason I want to remove one of the nickel coatings the more layers you put on it can chip. I can put on a layer of 24 kt over the copper, then finish with rhodium. I have…
-
Hello Everyone,I have my own jewelry business. Platinum does wear out a lot faster. Most of the items I electroplate are finished in rhodium. It holds up to more wear than most other coatings. Most rhodium coatings last about three to five years on a ring. Under the skin I imagine a lot longer. I am going to plate several…