xepicxmonkeyx
Comments
-
hallucinogens?
-
@Fireice289, have you ordered the 0.75mm x 1mm ones? Would they be big enough?
-
I just emailed supermagnetman.com and apperently they'll have N55 3x1 titanium nitride/parylene-C magnets for sale, late May early June!
-
Not sure if this has been said yet (not on computer so I can't CTRL-F it) but I just emailed supermagnetman.com and apperently they'll have N55 3x1 titanium nitride/parylene-C magnets for sale, late May early June!
-
Ok, cheers!
-
I was wondering about the strength of N35 magnets for sensitivity? I would of course prefer an N52 magnet but I can't find any with coatings I trust. I have found one with a Parylene-C coating but this one is N35, would this still be useful?
-
@TheGreyKnight, I ordered EMLA cream which is 2.5% Lidocaine and 2.5% Prilocaine!
-
...Well, That was a botch! I really fucked that surgery. Two incisions (somehow), One got subdermal the other barely a graze. Both were too thin, and only was it when the ice started to were off did realize I needed to stretch the fucker open! @TheGreyKnight, @Meanderpaul, I just ordered some numbing cream! Can't remember…
-
@SomeRandomGuy, I've just made the Isopropyl+Water ice cubes waiting for the spectators to arrive now. @Meanderpaul, I was going to get something like that, but I cannot find anywhere that sells it... Pharmacies etc, etc... especially in my area!
-
@ChrisBot Yeah... XDD Had a hunch!
-
@misslitty Ah, that won't be good then! :(
-
@SomeRandomGuy Yeah, I did come along that challenge. It's where the ice absorbs heat to dissolve the salt! I was thinking about doing that, but surely it must be a bit tendious doing it on the tip of your finger? Also, what's your thoughts on getting piss drunk before the procedure? I've got to be accurate with the…
-
P.S. Sorry for the multitude of question, just trying to assure I don't fuck up as the dreaded day approaches!
-
Also, in order to numb my finger as much as possible I was planning to freeze a solution of salt water. Salt water allows the water to reach much lower temperatures without freezing, and when it does freeze, it stays frozen for a lot longer. Would this solution be at all hazardous? Of course assuming the salt isn't the…
-
That's good to hear, was gonna go to the pharmacy today so I'll see about the Chlorhexidine gluconate. Cheers!
-
Yeah isopropyl, corrected!
-
@Zerbula Cheers for the advice, I was aware of the Au scraping against the tools, so I've planned to do it by hand then use a folded piece of paper to push it in even further. One question though, how badly is the isopropyl I'm using, for sterilisation, likely to damage the Au? And I'll definitely try to upload the entire…
-
@Zerbula, Unlikely! Of course if it is rejected, I'll take it out and apply another coating of some sort. But I'm hoping I can get away with not re-coating it!
-
@ChrisBot @misslitty @Zerbula Yeah, I've ordered a Gold plated 3x1mm N52 magnet... And of course, big thanks to all of you! @Zerbula, Honestly, this was just a lazy question. I was scowering all the coatings on the KJMagnets and researching them, leaving the nickel coating to last (I had an idea nickel coating was bad) so…
-
After how long it took me to find one, I'm assuming this question is still open. So the places I got mine was first at KJMagnet, as suggested above, but they didn't have any small enough, but I got a 6x1.5mm anyway. When it arrived it looked particularly big for my fingers so I've now ordered one from US eBay (I'm in…
-
@zerbula, not able to spot check right now, but even the rough results you've provided are fine. One last question though, due to the size of the magnet I don't want to have to place it in my finger, so how would placing it in the flap of fat under the pinky be? Of course if it significantly reduces the sensitivity even…
-
@Zerbula, Do you know if there'd still be enough sensitivity?
-
-
@Meanderpaul, no I did not have my finger turn green, but I do realise the hazards of putting pure neodymium into your body. @iamericami, Pure gold is quite easy to make if you have the money/time to buy a bunch of different solutions. And doing so would be quite reliable, But I just can't be arsed!
-
How long have Dangerous things been "changing suppliers" though, I think that was the first place I went back in July and it hasn't changed since. If what you say is true, and that they will have some next month, then fucking AWESOME!!! But right now, I'm in a state of despair.
-
@Meanderpaul I'll be spending $40 anyway... I'm sure shipping wont cost much!
-
Is there a site, UK based, where I could order a pre-coated magnet? I did try dangerous things, however they're "changing manufacturer(s)", making that option void! *Nice site BTW*
-
Ok, definitely sounds beyond my budget... Is there a £20 alt, by any chance? Titanium, maybe?